If you are an Ely tradesperson or fleet manager wondering exactly what getting van graphics fitted actually involves, here is the full process from first contact to driving away.
The process starts with a phone call or message. At this stage we need to know the make, model and year of your van, because panel shapes, body contours and handle positions vary significantly between vehicles - a Transit Custom is very different to a Sprinter, and even the same model changes between generations. We also need to understand what you want the graphics to do: are you after full branding with logo, imagery and contact details, or simpler lettering and a colour accent?
If you have an existing logo, send us the file. Vector files (AI, EPS or PDF) are the most useful because they can be scaled to any size without losing quality. If you only have a low-resolution image from a website or business card, let us know - we can advise whether it is workable or whether we need to redraw it. Many small businesses have logos that were designed for print but have never been prepared for large-format vehicle graphics, and that is something we sort out at the design stage.
We design the graphics in-house. That means we build the layout directly onto a template for your specific van model, so you can see roughly how the finished design will look across the actual panel shapes rather than on a generic rectangle. This is important because a design that looks balanced on a flat artboard can look very different once it wraps around a door recess or runs up to a wheel arch.
The design stage covers layout, typography, colour choices and where the joins between panels will sit. Joins should be planned at natural panel breaks - door edges, body lines, the edge of a door recess - so they are not visible in normal use. We show you the design as a visual before anything goes to print. If changes are needed, they happen at this stage while the job is still on screen, not after film has been cut and printed.
Colour on screen never looks identical to colour on printed vinyl in real daylight. We allow for this in the design process, but it is worth knowing before you get attached to an exact shade on your monitor.
Once the design is signed off, it goes to print. We print in-house, which means we control the output quality directly. After printing, the panels are laminated - a clear protective film is applied over the printed surface to protect it from UV, rain, pressure washing and abrasion. The laminated panels then need time to fully cure before application, so there is a short lead time between signing off the artwork and the fitting appointment.
During this time, your van should be as clean as possible before we arrive. A basic wash to remove heavy dirt and grime makes the preparation stage quicker when we get there. Any tar spots, bird lime or tree sap on the panels should be removed before the fitting date if possible, though we carry appropriate cleaning materials as part of our standard preparation process.
This is the stage that makes or breaks a graphics job, and it is where corners most often get cut. Every panel that will receive vinyl needs to be thoroughly cleaned, degreased and dried before anything is applied. That means a wash, a wipe-down with a panel-cleaning solvent and time for the surface to come up to the right temperature.
Vinyl film should not be applied to a cold, damp surface. In winter, this can mean allowing the van to warm up indoors or in a sheltered area before starting. We work at your premises in Ely, so if you have access to a garage or covered yard, that is useful.
Panel edges, door handles and bodywork recesses need particular attention. These are the points where adhesive bond is most likely to fail if preparation is rushed. We clean these areas separately and check for any surface contamination before the film goes anywhere near them.
The printed panels are applied section by section. Large panels are typically applied wet (using a water and mild detergent solution) or dry depending on the size, the film type and the complexity of the surface. Wet application gives more time to position large panels before the adhesive grabs, but it requires careful squeegee work to clear all moisture from underneath the film before it bonds.
Recesses, door handles and bodywork curves are worked with heat where needed - a heat gun allows the film to conform around tight curves without creasing or lifting at the edges. Applying heat to stretch film is a normal part of professional installation; it makes the film behave more like a skin rather than a stiff sheet.
Joins between panels are made at the planned positions. A straight, clean join at a natural panel break is effectively invisible at normal viewing distance. Where an overlap is unavoidable, the top layer is trimmed back so the overlap is minimal and sits flush.
Door seals, handles and trims are lifted where possible so that the film can be tucked underneath rather than just cut to the edge. A film that is tucked under a seal is far less likely to lift than one cut flush to the surface.
Once all panels are applied, every section is checked systematically. We look for any trapped air, any edges that need extra pressure, any section of film that has not bonded fully over a recess or contour. Small issues caught at this point are straightforward to fix. A panel with a persistent problem can be lifted and reapplied while everything is still in front of us.
The final check includes standing back and looking at the full van in context - checking that the design reads as intended, that any text is legible at a distance and that the joins are where they were planned to be.
After fitting, there are a few practical things worth knowing. Freshly applied graphics should not be pressure washed for at least 48 hours while the adhesive finishes curing. High-pressure jets directed at panel edges can lift film that has not yet fully bonded. Standard hand-washing is fine before that point.
Avoid automatic car washes with spinning brushes - these are hard on any vinyl film. Touchless jet washes are fine in normal use once the curing period has passed.
When it is eventually time to remove the graphics - at a rebrand, a vehicle sale or a lease return - we offer removal as a separate service. Vinyl removed with appropriate heat and care leaves the paint underneath undamaged. Film left on too long or removed without heat can be more difficult to lift cleanly, so it is worth planning removal before the graphics get to the brittle stage.
We travel to Ely for both fitting and removal jobs. The work is done at your location - your yard, depot or wherever the van is kept. If you want to talk through the process for your specific van and design requirements, give us a call and we can work through what is involved before anything is committed.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsLet us know what needs branding and we will send a design and price to look over.