Covering Cambridge and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Full Van Wraps in Soham - What to Do While You Wait (and What to Leave Alone)

If you're in Soham and you've booked a full van wrap - or you're deciding whether to - there's a lot you can do to prepare your vehicle and make the process go smoothly, and a few things that will cause problems if you try them yourself.

5.0 from 9 Google reviews Est. 2020 A written quote up front Mock-up on your vehicle type first We bring the fitting to you

What a Full Van Wrap Is

A full van wrap is a single, continuous printed film that covers every visible panel of the vehicle - sides, bonnet, roof, tailgate, wheel arches, door pillars and all the contoured sections in between. It is not a collection of individual stickers. The film is fitted as a complete livery, heat-formed around body lines and curves so it sits flat and consistent across the whole vehicle. The original paintwork underneath stays untouched and fully protected throughout.

We design and print everything in-house at our Cambridge base and travel to Soham and the surrounding area to carry out installation at your premises or chosen location. We also offer wrap removal when the time comes to rebrand or move the vehicle on.

What Happens Between Booking and Installation Day

Once you have confirmed a full van wrap, there is usually a period of a few days to a couple of weeks while the design is being developed and the film is being prepared. This is not dead time - it is a good opportunity to get the van into the best possible condition for installation, which directly affects the quality and longevity of the finished result.

What you can usefully do during this period:

  • Give the van a thorough clean, including areas that do not normally get much attention - wheel arches, the lower sills, the edges of doors and the area around badges and handles. Surface contamination is one of the most common causes of adhesion problems.
  • Remove any old stickers, decals or signage that you know is coming off. Use a heat gun or hair dryer on a low setting to soften the adhesive, then peel slowly. Clean up any residue with a suitable adhesive remover and wash the area thoroughly afterwards.
  • Check the paintwork in good daylight and note any rust spots, bare metal, chips or flaking paint. These need attention before the wrap goes on - not because they will be visible through the film, but because they will affect adhesion and can trap moisture underneath.
  • If the van has recently been resprayed, make sure the new paint is fully cured. Fresh paint that has not fully hardened can be damaged during wrap installation. Ask the bodyshop how long they recommend waiting before wrapping.

What Not to Do Before the Installer Arrives

There are several things that people do with good intentions but which cause real problems on installation day. The most common is waxing or polishing the van. A freshly waxed van looks great but it is one of the worst surfaces for a wrap adhesive to bond to. Silicone residues from wax and polish products prevent proper adhesion and can cause lifting within days of installation. If you have polished the van recently, tell the installer - the surface will need decontamination before anything goes on.

Similarly, applying any kind of plastic or rubber trim dressing to the edges of panels or door seals is counterproductive. These products migrate onto the adjacent paint surface over time and create the same adhesion problem as wax.

Do not attempt to remove badges or trim pieces yourself unless you are certain of what you are doing. Badges on modern vans are often bonded with strong adhesive tape and removing them incorrectly can chip or crack the surrounding paint, creating a problem that then has to be dealt with before the wrap can go on. If badges need to come off, discuss it with the installer first.

Do not apply touch-up paint to chips or scratches in the days before installation. Touch-up paint needs time to cure fully - at least several weeks - before it is ready to have film laid over it. Fresh touch-up that is not fully hardened will not bond properly and can be pulled away when the wrap is eventually removed.

Preparing the Space for Installation

Because we come to you, the installation takes place at your premises. The space where the van is parked makes a difference to how smoothly the job goes. A few practical points:

  • An indoor space - a garage, unit or workshop - is significantly better than an outdoor area. Dust, wind and fluctuating temperature affect film application, particularly when working on larger panels.
  • If indoor space is not available, a dry, still day is preferable to a windy one. Cold and damp conditions slow the adhesive and can affect how the film bonds to the surface.
  • Make sure there is enough clearance around the van for the installer to work on all sides - roughly a metre on each side and at the front and rear.
  • Good lighting helps the installer spot any surface contamination or imperfections before the film goes on. If the space is dark, it is worth arranging additional lighting.

On the Day Itself - What to Expect

A full van wrap on a standard panel van takes the best part of a day. A large high-roof Sprinter or Transit can take longer. The installer will prepare the surface first - cleaning, degreasing and in some cases removing badges or trim - before the film is applied. This preparation stage is not something to rush or skip. The time spent on surface prep is directly reflected in the longevity of the finished wrap.

During installation, try to keep the area clear and avoid anything that creates dust or debris nearby. If you are working in a yard or unit, hold off on any sweeping, grinding or other dusty activities while the film is being laid.

Once the wrap is complete, the film needs time to cure - typically 48 to 72 hours before the van goes through any kind of pressure wash or is exposed to heavy rain. We will confirm the specifics on the day based on conditions.

What You Should Never Attempt Yourself

It is worth being direct about this, because there is a lot of online content about DIY van wrapping. Full van wraps are not a DIY job for a working van. The scale of the panels, the number of complex junctions around doors, handles and mirrors, and the skill involved in stretching film correctly around curves without introducing stress points or bubbles all require specific tools and significant hands-on experience. A partial or failed DIY wrap also creates problems for a professional to fix afterwards - in some cases the film damage or residue left behind means additional preparation work and cost.

The one thing you can safely do yourself in advance is clean the van thoroughly. Beyond that, let the installer take over.

Ready to Get Started

We serve Soham and the surrounding area from our Cambridge base. Full van wraps for a mid-size panel van typically sit in the range of £1,500 to £2,500 depending on the design and vehicle size - larger vans with high roofs and complex body shapes will cost more. If you are ready to discuss a wrap for your van or small fleet, call us and we will talk through what is involved before anything else is agreed.

Working with us in Soham

  • Design and print both done by us, not sent out.
  • Old lettering or wraps removed first, if needed.
  • Fleet work in Soham split into stages.
  • Artwork stored, ready for your next vehicle.

Full Van Wraps in Soham?

Let us know what needs branding and we will send a design and price to look over.

Call Quote