If you're arranging commercial vehicle wrapping in Soham, there are useful things you can do in advance - and some things you should definitely leave alone.
A commercial vehicle wrap is a printed or cut-vinyl graphic applied by hand to the exterior panels of your van, pickup truck, minibus or specialist work vehicle. It carries your business name, contact number, logo and livery colours wherever the vehicle travels. The vinyl bonds to the painted surface with a pressure-sensitive adhesive and is removed cleanly when you need to update or retire it.
The process covers design, print and fitting. Done well, the finish is sharp and weather-resistant. The fitter works panel by panel, cutting and heat-forming the vinyl to match the bodywork precisely - around door handles, mirrors, recesses and contoured edges.
Between booking your wrap and the fitting date, there is usually a design and proofing stage. You will be asked for your logo files, colour references and any brief on layout. We design in-house, so this stage is under our direct control - you review a scaled proof of the artwork on your specific vehicle before anything is printed. Use this period well and the actual fitting day will run smoothly.
The single most useful thing you can do before a fitting is clean the vehicle thoroughly. Surface preparation is critical to how well vinyl bonds - grime, wax, polish and traffic film all interfere with adhesion. Wash the vehicle with a clean vehicle shampoo and rinse it well. Pay particular attention to the lower panels and sills where road grime builds up, and around door handles and mirrors where wax tends to accumulate.
Do not apply any new wax or polish before the fitting. Even a light coat of polish creates a barrier the adhesive cannot grip through, and it is one of the most common causes of early edge lifting after installation.
Vinyl goes over paint, not over filler, rust, peeling lacquer or unrepaired dents. If there are dents with cracked paint, any bubbling from underneath, or areas of surface rust on the lower sills or wheel arches, have these repaired and the panels properly resprayed before the fitting date. Applying vinyl over damaged paint traps the problem underneath, and when the wrap eventually comes off, the paint damage will be worse than when it went on.
Minor shallow dents in otherwise sound paint can usually be wrapped over without issue - ask us if you are unsure about a specific area.
The design proof stage is where most delays happen. If you have all your brand assets ready - vector logo files, correct colour codes, up-to-date phone number and website address - the design process moves quickly. If you need to chase a logo file from a designer, or you are unsure which version of your phone number to use, sort this before you call to book, not after.
Also decide what information the vehicle needs to carry. Name, number and trade are the minimum. Some operators add a website, a service area, or a short list of what they do. Too much text at small point sizes becomes unreadable at speed, so less is usually more - but think it through in advance so the design brief is clear when you give it.
Some vehicles have areas you may not want wrapped - sensors behind the bodywork, cameras, charging flap covers on electric vehicles, or areas due for a repair. Make a note of these before the fitter arrives so they can be discussed at the start of the job, not discovered mid-way through.
It is worth being direct about this, because the temptation to get started on a job yourself is real for tradespeople used to working independently. With vehicle wrapping, there are several things that cause serious problems when done without the right materials and training.
We travel to your premises and work at your location in Soham, so the vehicle stays on your site. Have it parked out of direct rain if possible - not because a damp vehicle cannot be wrapped, but because drying the panels takes time and reduces the working window. A covered yard, garage or open barn is ideal. A clean, dry surface to work around the vehicle is helpful.
Set aside enough time for a full van wrap. Partial wraps and cut vinyl graphics take less. If you have multiple vehicles being done in one visit, let us know in advance so we can plan the day accordingly.
Once the vinyl is on, the adhesive continues to cure for a short period. Avoid jet washing or putting the vehicle through an automatic wash for the first few days. Hand washing with clean water is fine. Keep it out of prolonged direct sunlight immediately after fitting if you can. After the initial cure period, the wrap can be washed normally - just avoid abrasive products and pressure washing aimed directly at panel edges.
Van Wrapping Cambridge serves Soham and the surrounding area. We design and print in-house, travel to your site to fit, and handle removal of existing graphics when needed. If your vehicles are ready, or you just want to talk through the job before committing, call us and we will walk through the whole process with you.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsA full van wrap transforms your entire vehicle into a moving advertisement for your business.
See detailsLet us know what needs branding and we will send a design and price to look over.