Covering Cambridge and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Full Van Wraps in Cambourne

If your van's livery is fading, peeling or just not pulling its weight on the road, a full van wrap fitted at your premises in Cambourne is the most effective way to fix that.

5.0 from 9 Google reviews Est. 2020 A written quote up front Mock-up on your vehicle type first We bring the fitting to you

What a full van wrap actually involves

A full wrap covers every visible panel of your van in a single, continuous printed film. That means the sides, bonnet, roof, rear doors, bumpers and mirrors are all brought into one coherent design. There are no half-measures, no colour breaks and no bare metal or faded paint showing through. The result is a vehicle that looks purpose-built, not patched together.

We design and print everything in-house, then come to you. The installation happens at your premises in Cambourne, so your van stays close to base and you lose the minimum amount of working time.

Warning signs your current livery or paintwork needs attention

Most van owners notice the obvious things first: peeling graphics, bubbling vinyl or large patches of bare paint where old lettering has been stripped off badly. Those are the cases where something has clearly gone wrong. But there are earlier warning signs that are easy to miss until the damage becomes expensive.

Colour fade is one of the most common. Printed vinyl that has been on a van for several years will begin to lose its vibrancy, particularly on the roof and upper sides where UV exposure is greatest. The van still looks fine in a dark car park, but in full daylight the colours appear washed out and inconsistent. That sends the wrong message to any potential customer who sees the vehicle.

Lifting edges are another early sign. Vinyl lifts at corners, door edges and panel creases when either the original preparation was poor or when the film used was not suited to the vehicle's contours. Once an edge begins to lift, water and grit get underneath and the problem accelerates. A small lift at the bottom of a rear door can become a metre-long peel in a single winter.

Silvering is worth knowing about. This is where the adhesive bond between the vinyl and the panel breaks down in patches, creating a silvery, mottled look when you look at the van at an angle. It is caused by either a poor installation surface or a film that has simply reached the end of its useful life. It cannot be repaired in sections without the repair being visible.

Cracking along fold lines happens on vans that have had a wrap for a long time, especially in exposed locations. The film becomes brittle and micro-cracks appear wherever the vinyl had to flex around a curve or a pressed edge. Once cracking begins, moisture works its way in and the wrap starts to fail structurally.

What causes these problems in the first place

Poor surface preparation is the single biggest cause of premature wrap failure. If the van's paintwork is not thoroughly cleaned, degreased and dried before installation, the adhesive bond is compromised from day one. Invisible contamination - road film, polish residue, silicone from rubber seals - all prevent the vinyl from sticking properly.

Panel damage matters too. Dents and deep scratches create edges under the vinyl where the film cannot conform fully to the surface. Those points become stress concentrators and the wrap lifts there first. A good installer will flag any panel issues before the film goes on.

Incorrect film choice for the application also causes problems. Not all vinyl films behave the same way. Calendered films are less conformable than cast films and can spring back from tight curves over time, creating lift at complex areas like wheel arches and door handles. Cast films are significantly more flexible and are the right choice for a full wrap on any van with normal body contours.

Poor heat forming during installation leads to stress in the film. Vinyl needs to be warmed and stretched correctly around compound curves. If it is forced into place cold, internal stress builds up in the material and it will eventually pull back. This is most obvious on wing mirrors, door handles and the front bumper.

Finally, damaged or uneven factory clear coat is a common underlying cause that gets overlooked. If the van's original lacquer is peeling or has been spot-repaired with mismatched products, the vinyl will not bond evenly and the problem shows through the film.

What to check before you have a wrap installed

Before any installer puts vinyl on your van, the surface preparation should be discussed openly. Ask what cleaning process they use and whether they inspect the paintwork for damage first. Any competent installer will walk around the vehicle with you beforehand and point out anything that could affect the result.

Check whether the design is being printed in-house or outsourced to a third party. In-house printing means the installer controls the colour output, the material specification and the print resolution. It also means any reprint, whether for a colour match issue or an additional vehicle, comes from the same setup and matches precisely.

Ask about wrap removal. Full wraps do come off, and when the time comes to rebrand or sell the vehicle, the removal process matters. Film that has been on a van for many years can be more difficult to remove cleanly, particularly if the van's paintwork was not in good condition underneath. A business that offers removal as well as installation understands the full lifecycle of the product.

How a full wrap compares to a repaint or partial livery

A full wrap protects the original paintwork underneath. When removed carefully, the panels beneath should be in the same condition as the day the wrap went on. That has real value when the van goes back to a lease company or is sold. A repaint, by contrast, is a permanent change that affects residual value and cannot be undone.

Partial liveries - side graphics, rear lettering and a logo on the door - are cheaper and have their place. But they leave large areas of plain or faded paintwork visible, which limits the impact of the design. A full wrap treats the van as a single canvas and allows designs that would be impossible with cut vinyl alone.

Sizing, timescales and what to expect on the day

Full wrap pricing varies by van size. A compact panel van will cost less than a high-roof long-wheelbase Transit or Sprinter because there is simply less surface area to cover. As a rough guide, full wraps on vans in the UK currently run from around £1,500 for a small van up to £3,500 or more for a large high-roof vehicle, depending on design complexity and film specification. These are market-typical figures and your quote will reflect the specifics of your vehicle.

Installation typically takes one to two full days depending on the van. Complex designs with lots of small elements, or vans with heavily contoured bodywork, take longer. The van needs to be clean, dry and available for the full installation period. We come to your site in Cambourne, so you can keep working around us.

Get a quote for your van

Send us photos of your van, tell us your rough requirements and your location in Cambourne, and we will come back to you with a clear price. If you have an existing design file we can work from that, or our in-house design team can build something from scratch. Call us to talk through what you need.

Working with us in Cambourne

  • Design and print both done by us, not sent out.
  • Old lettering or wraps removed first, if needed.
  • Fleet work in Cambourne split into stages.
  • Artwork stored, ready for your next vehicle.

Full Van Wraps in Cambourne?

Let us know what needs branding and we will send a design and price to look over.

Call Quote