If your van or work vehicle isn't turning heads for the right reasons, commercial vehicle wrapping in Cambourne can fix that fast.
A commercial vehicle wrap is a layer of printed vinyl film applied directly to your van, pickup, minibus or specialist work vehicle. The vinyl is cut and fitted to the contours of the bodywork, covering panels, bumpers, mirrors and door handles as far as your design requires. At Van Wrapping Cambridge we design and print everything in-house, then come to you, fitting the wrap at your premises or yard in Cambourne rather than asking you to drop the vehicle off elsewhere.
The process starts with a design consultation. We take your logo, brand colours and any copy you want to show, then produce a visual proof scaled to your specific vehicle. Once you approve the design, we print it, laminate it for surface protection, and book a fitting day that suits your schedule.
This is where most tradespeople and small fleet managers in Cambourne miss money. Your van is moving around Cambridgeshire every day. It is parked outside jobs, on retail car parks, in queues. If the graphics are not right, every one of those moments is a wasted impression.
Here are the warning signs that your current setup is failing you:
Poor preparation is behind most wrap failures. Vinyl needs a clean, contaminant-free surface. Grease, wax, silicone polish and even light road film will prevent proper adhesion. A wrap fitted over a recently waxed panel may look fine for weeks, then start to lift as the adhesive fails to bond fully.
Cheap or inappropriate vinyl grades are another common cause. There is a significant difference between the film used for short-term promotional graphics and the cast vinyl used for a vehicle that works outdoors every day for several years. Calendered vinyl, used for flat surfaces and indoor applications, can shrink and crack when wrapped around compound curves. Cast vinyl conforms better to complex shapes and holds its dimensions over time. We use exterior-grade cast vinyl film as standard for all commercial vehicle work.
Incorrect fitting temperature also causes problems. Vinyl applied in very cold conditions becomes stiff and difficult to stretch around curves without tension in the film. That tension can cause lifting later. We plan fitting days to avoid extremes where possible, and where a vehicle must be wrapped in a cold yard, we allow material to acclimatise before we start.
Finally, design errors cause silent failure. A wrap that looks good in a small on-screen preview may be illegible at vehicle scale. Viewing distance matters. Text that is too small, contrast that is too low, or colours that clash with the vehicle base colour all reduce the effectiveness of the graphic even when the material itself is fitted perfectly.
Run your hand along the edges of any existing graphics on your van, particularly around door handles, wheel arches and panel joins. Any lifting or bubbling at those points needs attention. Check the colour of printed areas against a printed copy of your logo or brand guidelines. Hold them side by side in natural daylight. If there is a visible difference, the graphics have faded enough to be replaced.
Look at the rear of the vehicle, which takes the most road grime and stone chip impact. Chips through printed vinyl to bare metal will eventually rust if not addressed, and that is a bodywork repair cost on top of a re-wrap cost.
Not every job needs a full wrap. A full wrap covers the entire vehicle and gives you maximum visual impact. It also protects the original paintwork underneath, which matters if you lease the vehicle and need to hand it back in good condition. Full wraps are priced by vehicle size and design complexity. For a standard medium wheelbase van, expect to pay in the region of £1,500 to £3,000 depending on design and coverage.
A partial wrap covers key panels only, typically the sides and rear, leaving the cab or roof in the vehicle's base colour. This is a cost-effective option when your brand works well on a coloured background and you want to keep investment lower. Partial wraps on a standard van typically run from around £600 to £1,500.
Cut vinyl graphics use a plotter cutter to produce lettering and shapes from single-colour vinyl film. There is no printed image, just clean vector-cut text and logos. This is the right choice for simple, legible business information: your trade, your number, your website. Cut vinyl is durable, straightforward to apply and easy to remove cleanly. For a basic cut vinyl package on one van, budget from around £150 to £400.
We also remove existing wraps and graphics. Vinyl that has been on a vehicle for several years can be more difficult to remove cleanly, particularly if it has been exposed to prolonged heat. The adhesive can transfer to the paintwork and require chemical cleaning. Wraps removed within their expected lifespan typically come off more cleanly. If you are removing graphics before returning a leased vehicle, book the removal early enough to allow any adhesive residue to be treated properly.
We travel to customers across Cambridgeshire, so there is no need to arrange transport to a workshop or leave your vehicle somewhere overnight. Bring us your existing brand assets, or we can build a design from scratch based on your business type and what you want customers to know.
Call us to discuss your vehicle and what you need from the graphics. We will tell you honestly what format and coverage will work best for your situation, and give you a clear price before any work starts.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsA full van wrap transforms your entire vehicle into a moving advertisement for your business.
See detailsLet us know what needs branding and we will send a design and price to look over.