If your Cambourne business runs multiple vehicles and they don't all look the same, you're leaving brand recognition on the table every time one of them pulls up on a job.
Fleet livery problems rarely appear overnight. They creep in gradually, and by the time customers or staff notice, the damage to your image is already done. Knowing what to look for means you can act before a small issue becomes an expensive one across your whole fleet.
The most common warning sign is fading. Printed graphics and solid-colour wraps both fade with UV exposure over time, but they don't all fade at the same rate. A van bought two years after the rest of your fleet will look noticeably brighter, and side-by-side on a customer's driveway that contrast is hard to miss. If you're running four or five vehicles and they all went on at different times, colour drift across the fleet is almost inevitable without active management.
These are the signs worth acting on before they worsen:
Poor preparation is behind most wrap failures. The vehicle surface must be completely clean, dry and free of wax, silicone and grease before any film goes on. Workshops that rush this stage create bubbling and poor adhesion from day one. Any panel damage, filler, or previous body repairs should be declared before wrapping, as repaired areas can behave differently under film and lead to early lifting.
Film quality and specification matter too. Calendered films are cheaper but less conformable, meaning they struggle on complex curves and compound shapes. Cast films are more expensive but significantly more durable and better suited to full wraps on vans with deep recesses. Using the wrong spec for the job is a common source of premature failure, particularly on the shoulder lines and rear doors of panel vans where the geometry is demanding.
Temperature during installation also plays a role. Film applied in cold conditions is stiffer and harder to work, increasing the risk of overstretching. At the other extreme, applying in direct sunlight causes the film to tack too quickly and limits the installer's ability to reposition. Professional installation in a controlled indoor environment avoids both problems.
A fleet wrap project for a Cambourne business starts with a design conversation. We work up the layout in-house, so there's no waiting on a third-party designer and no telephone-game between design and print. Colour matching across vehicles is done digitally before anything is printed, which is how consistency is achieved even when vehicles are different makes or body styles.
Print and cutting are handled on our own equipment, which means we control the output quality and can reprint a panel quickly if something isn't right before it goes on the vehicle.
We come to you. Installation happens at your premises or wherever your vehicles are based, so your operations aren't interrupted by needing to drop vans off at a workshop. For fleets of three or more vehicles we can stage the work so that not all of your vehicles are unavailable at the same time.
When a wrap reaches the end of its life, or when your branding changes, the old film needs to come off cleanly. We offer wrap removal as a standalone service. Done properly, with heat and the right tools, removal leaves the underlying paintwork in good condition. Done badly, it tears the film into small pieces that take hours to pick off and can pull up paint on older vehicles. If you're taking on a used vehicle that has someone else's livery on it, ask about removal before you assume the paint underneath is usable.
These are the questions worth asking any supplier, including us:
Full van wraps in the UK typically run from around £1,500 to £3,000 per vehicle depending on van size, the complexity of the design and whether the wrap is a solid colour change or a full printed livery. Partial wraps and cut vinyl graphics cost considerably less. For a fleet, the per-vehicle cost can reduce when vehicles are done in a batch because setup, design and colour profiling costs are spread across multiple units.
Phased projects - where you wrap vehicles as the budget allows - are entirely workable, provided the design and colour profile are fixed at the outset so later vehicles match the ones done first.
Call us to talk through what your Cambourne fleet needs and get a clear figure based on the actual vehicles you're running.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsA full van wrap transforms your entire vehicle into a moving advertisement for your business.
See detailsLet us know what needs branding and we will send a design and price to look over.