Part wraps for vans in Royston vary more in price than most people expect - here's a plain-English breakdown of what drives the cost up or down and what you're actually paying for.
A part wrap price covers four things: design and artwork, print and materials, preparation of the vehicle, and fitting. Each of these has its own cost drivers. Understanding which part of the price is doing the work helps you compare quotes properly rather than just looking at the bottom line.
Part wrap prices in the UK typically range from around £150 for a simple cut-vinyl panel up to £800 or more for large printed sections covering multiple panels on a full-size van. The variables that push you towards one end of that range or the other are mostly predictable.
The most obvious factor is how much of the van you're covering. A single rear door on a small panel van uses far less material and takes far less fitting time than both rear doors plus the offside sliding door on a Sprinter or Transit. Material is priced roughly by square metre, and fitting time scales with the area being covered - so a larger job costs more on both counts.
The shape of the panel matters too. A flat, rectangular rear door is straightforward. A bonnet with a pronounced ridge running down the centre, or a panel with deep recesses and moulded features, requires more skill and time to wrap without lifting. Complex panel shapes take longer to fit properly and that's reflected in the price.
Van dimensions vary significantly. A Transit Custom and a Sprinter might look broadly similar, but the Sprinter has considerably larger panels. A rear door on a large panel van can be nearly twice the area of the same panel on a smaller van. If you're asking for a quote, have the make, model and year ready - a price given without knowing the specific vehicle is unlikely to be accurate.
Some van models have panel shapes that are simply more awkward to work on. Deep pressed features, raised ribs and complex curves all add time to the fitting process and affect the final price.
There is a meaningful difference in cost between entry-level calendered vinyl and the cast films used in professional vehicle wrapping. Cast film costs more to buy, but it conforms properly to curved panels, is more dimensionally stable over time and lasts longer in good condition. Calendered film is cheaper upfront but tends to shrink and lift at the edges sooner, particularly on panels that aren't completely flat.
A quote built on cheap calendered material will look attractive initially. The practical difference becomes apparent a year or two later when edges start lifting and the finish looks tired. If two quotes are significantly different in price on what appears to be the same job, the material grade is often the explanation.
All our part wraps use cast vinyl. We don't offer a cheaper calendered option because the results aren't something we're happy to put our name to.
Printed part wraps should always have a laminate applied over the print. The laminate protects the inks from UV degradation, fuel splashes and abrasion. Without it, printed graphics fade faster and are more easily scratched. Laminate adds to the material cost but is a standard part of a properly done printed wrap.
Some very low-cost suppliers leave out the laminate to hit a headline price. Always confirm that the quote you're looking at includes a laminated print, not unprotected ink on bare film.
If you have print-ready artwork - a properly built file at the right resolution with the correct colour format for print - design cost is minimal. The file needs checking and setting up for the specific panel dimensions, but that's a quick job.
If your existing logo is only available as a low-resolution image - a small JPG from your website, for example - it may need to be rebuilt as a vector file before it can be used for large-format print. That takes time and adds to the cost. The same applies if you need a full design built from scratch.
It's worth asking any supplier whether the quote includes design work, or whether that's priced separately. We handle design in-house, so there's no separate studio invoice - but the amount of design work involved affects the overall price.
If your van has existing lettering or graphics that need to come off before new vinyl goes on, removal adds to the job cost. The time required depends on how the original graphics were applied, how old they are and what condition they're in. Old vinyl that's been on a hot van for several years can be more stubborn than recent work.
Removal needs to be done carefully to avoid damaging the paint underneath. Heat is used to soften the film before peeling, and adhesive residue is then cleaned off. If this stage is rushed, the result can be paint damage or adhesive contamination on the panel that affects how the new vinyl bonds.
We offer removal as part of the service. If your van needs this, tell us upfront so we can allow the right time and price it accurately.
If you're running a small fleet in Royston and several vans need the same treatment, the per-van cost can come down. Set-up and design work applies once across the fleet rather than being charged per vehicle. If you have more than two or three vans, it's worth asking about fleet pricing rather than treating each van as a separate job.
The number of colours in your design doesn't affect the print cost on a wide-format digital printer - full colour is printed in a single pass, so a complex multi-colour design costs the same to print as a two-colour one. The cost driver is the size of the print, not the number of colours.
Similarly, the complexity of the artwork in terms of creativity doesn't automatically push the price up - straightforward layout work on a simple logo is quick regardless of how bold the design looks on the finished van.
Vague quotes based on a phone description of your van are rarely accurate. For a proper price, we need to know the make, model and year of the van, which panels you want wrapped, what the design involves and whether removal of existing graphics is needed. If you can send a photo of the panels along with your enquiry, that helps too.
We design and print in-house, and we come to your premises in Royston so you don't need to move the van. Call us with your requirements and we'll give you a straight price based on the actual job.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsLet us know what needs branding and we will send a design and price to look over.