If your van is due a wrap or your existing graphics are starting to fail, knowing the warning signs early saves you money and keeps your business looking sharp around Haverhill.
Most tradespeople notice a problem with their van graphics too late - when a customer points it out or the vinyl starts peeling on a job. A wrap that is deteriorating does active harm to how your business is perceived. The good news is that the signs of a failing or overdue wrap are easy to spot if you know what to look for.
The most obvious sign is vinyl that has started to lift at the edges, particularly around door handles, wheel arches or the base of panels where the film wraps tightly around curves. Once an edge lifts, water and grit get underneath and the bond breaks down faster from that point outward. A small lift at a corner can become a full panel failure within a few months if left untreated.
The cause is usually age combined with repeated washing - especially pressure washing too close to the edges. It can also happen when a wrap was fitted without adequate heat-forming around complex curves, so the film was never fully bonded in the first place.
Printed vinyl film has a finite outdoor lifespan. As it ages, colours shift - reds go orange, blues go grey, and bright whites take on a chalky, dull appearance. If your van livery looked vibrant when it was fitted and now looks washed out, the film has degraded. This is not just cosmetic: faded graphics tell potential customers the business they represent is not on top of things.
The rate of fade depends on the quality of the film used and how the van is stored. A vehicle parked outdoors facing the same direction every day will fade unevenly. The side that catches the most sun degrades fastest, so you can end up with a van that looks noticeably different on each side.
Bubbles under the film that were not there when the wrap was first fitted usually mean moisture has found a way in, or that the original application had air pockets that were not fully worked out. Small bubbles sometimes settle on their own in the first day or two after fitting - this is normal. Bubbles that appear later and grow are a sign of adhesion failure.
Silvering - where the film looks like it has a crinkled or metallic sheen in patches - is a related issue. It tends to happen when the adhesive has broken down or when the van's paintwork underneath was not properly decontaminated before the wrap was applied. Neither problem repairs well with a patch; at that stage the affected panel usually needs a full re-wrap.
Vinyl film that has been on a van for a long time, or that was lower quality to begin with, eventually becomes brittle. You will see hairline cracks, especially at the edges and anywhere the film flexes regularly - like door seams. Brittle film is very difficult to remove cleanly. The longer you leave it, the harder the removal job becomes and the greater the risk of adhesive residue staying on the paintwork.
If you are planning to sell the van, this matters a great deal. A wrap removed in good time leaves the original paintwork intact and the vehicle more attractive to buyers. A crumbling old wrap that has to be scraped off is a different story.
Not all warning signs are physical. If your phone number has changed, your services have expanded, you have rebranded or simply upgraded your logo, then the graphics on the van are sending the wrong message even if the vinyl itself is in reasonable condition. Outdated contact details on a van can cost you work - a customer who noted your number from the side of your van six months ago and finds it no longer works is gone.
Understanding what causes early failure helps you get better value from a new wrap. The main causes are:
If you have noticed one or more of these signs on your van, the first step is to assess how widespread the problem is. A single lifting edge caught early can sometimes be re-bonded without a full re-wrap. Fading, cracking or widespread adhesion failure across multiple panels means a full replacement is the right call.
We design and print in-house and travel to customers in Haverhill and the surrounding area, so the work is done at your premises or wherever suits you. If you are not sure whether your existing wrap can be saved or needs replacing, give us a call and describe what you are seeing - we can usually give you a clear steer without needing to see the van first.
We also carry out wrap removal as a standalone job. If you are rebranding, selling the van or simply want the original paint back, removal needs to be done carefully to avoid damage. Heat is applied to soften the adhesive, and the film is peeled back steadily. Any adhesive residue left behind is treated with the correct solvent. Done properly, the original paintwork underneath should be in the same condition it was in when the wrap went on.
If you have a Haverhill-based van that needs new graphics, a full re-wrap or just a clean removal of old livery, call us to talk through what is needed. We will tell you straight what the job involves and what it will cost before anything is agreed.
Also available
We wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsA full van wrap transforms your entire vehicle into a moving advertisement for your business.
See detailsLet us know what needs branding and we will send a design and price to look over.