Covering Cambridge and the surrounding area Monday to Friday 9:00am - 5:00pm Get a quote

Fleet Wrapping and Branding in Trumpington - Keeping Your Livery in Good Shape

Getting your fleet wrapped in Trumpington is an investment, and what you do in the months and years afterwards determines how long that investment lasts and how professional your vehicles keep looking on the road.

5.0 from 9 Google reviews Est. 2020 A written quote up front Mock-up on your vehicle type first We bring the fitting to you

What Fleet Wrapping Involves

Fleet wrapping applies vinyl film to your business vehicles - either as a full colour change, a printed livery, or a combination of both. The result is a consistent, professional appearance across every van in your fleet, with your logo, trading name, contact details and brand colours reproduced identically from one vehicle to the next.

A properly managed fleet job covers design, print and installation, usually sequenced so that only one or two vehicles are taken out of service at a time. We design and print in-house and travel to your premises to carry out the work, so your fleet stays at your location throughout the process.

Why Aftercare Matters More Than Most People Expect

A wrap applied in quality cast film by an experienced fitter will look sharp for years - but only if it's maintained correctly. The two most common reasons wrapped vans look worse than they should after twelve months are incorrect washing technique and neglect of small edge lifts that grow into larger problems.

Neither issue is complicated to avoid. A few straightforward habits will keep your livery looking as good as the day the job was finished and extend the period before you need to think about replacement or repair.

Washing: What to Do and What to Avoid

Washing is where most damage to wrapped vehicles happens, and it's entirely avoidable. The key rules are:

  • Hand wash wherever possible. A bucket, a soft microfibre cloth and a mild, pH-neutral vehicle shampoo are all you need. This is the gentlest method and the least likely to cause problems.
  • Avoid automatic brush car washes. The rotating brushes found in drive-through washes are abrasive against vinyl film and can catch edges, causing lifting and tearing particularly around door handles, mirrors and body creases.
  • Touchless jet washes are acceptable with care. If you're using a pressure washer or a touchless wash bay, keep the lance at least 30cm from the surface and avoid directing the jet at a sharp angle along the edge of any panel. High pressure water driven under a film edge is one of the fastest ways to start a lift that then spreads.
  • Don't use petrol-station forecourt wipes. The cleaning solvents in many forecourt products are too aggressive for vinyl and will dull or streak the surface.
  • Wash more frequently in winter. Road salt attacks the adhesive layer at exposed edges. Vehicles that pick up heavy road salt and are left without washing for weeks are far more likely to develop premature edge lifting than those washed every week or two.

Routine Checks Your Drivers Can Do

Ask your drivers to do a quick visual check of their van's livery every few weeks. This takes under two minutes and catches problems before they escalate. What to look for:

  • Any corner or edge of film that has started to lift, particularly around door handles, the top of rear doors and the lower sills where grit and water collect
  • Bubbles that weren't there before - a small isolated bubble can sometimes be pressed back down when the van is warm, but a spreading cluster needs professional attention
  • Any scuffs, tears or gouges from minor impacts that expose the paint beneath - these let moisture in and can allow rust to begin under the film if left unattended
  • Lifted film at seams, where two panels of wrap meet - seams that were applied cleanly can lift over time if the vehicle is regularly exposed to pressure washing along that line

Catching a 5cm edge lift early costs very little to fix. Leaving it for six months can mean re-doing a full panel.

What You Can Fix Yourself and What You Can't

There is very little on a wrapped vehicle that a driver should attempt to fix themselves. The temptation when a small corner lifts is to press it back and secure it with tape or a household adhesive. Don't. Tape leaves residue that makes proper re-adhesion difficult, and the wrong adhesive can stain or permanently mark the film.

The one thing that is safe to do yourself is warming a small lifted edge gently with a hairdryer and pressing it back down firmly with clean fingers - this works on fresh lifts where the adhesive is still viable. Anything more than a few centimetres, or any lift that has been there long enough for dust and grit to get underneath, needs to be done by someone with the right tools and materials.

Similarly, do not attempt to remove a wrap yourself. Vinyl film needs to be warmed to the correct temperature and peeled at a consistent angle to come away cleanly. Too cold and it tears into small pieces; too fast and it pulls paint. We offer removal as a service and carry it out at your location.

Protecting the Surface Between Washes

A light application of a vinyl-safe detailing spray after washing helps the surface shed water and reduces the amount of grime that bonds to it between washes. These products are available from most vehicle detailing suppliers. Do not use wax-based products on printed livery - wax can cause the surface to become patchy and can build up around textured areas in the print.

Matte or satin finish wraps need particular care. Even light scratches from wiping with a dry cloth are visible on matte surfaces in a way they aren't on gloss. Always use a damp cloth and a dedicated matte-safe product on these finishes.

Planning for the End of the Wrap's Life

Even a well-maintained wrap on a working fleet vehicle will eventually reach the point where it needs to come off - either because the design is changing, vehicles are being sold or returned, or the film has simply reached the end of its serviceable life. A quality cast film applied correctly to a properly prepared surface should remain removable without damaging the paintwork beneath it for a number of years, but the longer it stays on beyond its natural lifespan, the more difficult and risky removal becomes.

Build removal into your planning when you commission the original wrap. Ask your contractor whether they offer removal as part of their service. We do - it's part of managing the full life cycle of your fleet branding, and we carry it out at your premises in and around Trumpington.

Talk to Us About Your Fleet in Trumpington

If your current livery needs attention - whether that's a repair, a full refresh or just advice on what maintenance your drivers should be doing - call us and we'll talk it through with you.

Working with us in Trumpington

  • Design and print both done by us, not sent out.
  • Old lettering or wraps removed first, if needed.
  • Fleet work in Trumpington split into stages.
  • Artwork stored, ready for your next vehicle.

Fleet Wrapping and Branding in Trumpington?

Let us know what needs branding and we will send a design and price to look over.

Call Quote