When your van's part wrap in Saffron Walden is looking tired or damaged, the choice between repairing what's there and starting fresh with new graphics is not always obvious - but it usually comes down to a few clear factors.
A part wrap is vinyl applied to specific panels of your van - rear doors, side panels, bonnet or tailgate - rather than covering the entire vehicle. It gives your business a branded, professional look without the cost of a full wrap. The vinyl is printed with your design, cut to fit the panel, and heat-applied so it conforms to the surface.
Part wraps are widely used by tradespeople and small fleet operators because they let you brand a vehicle quickly and change the design when your details or branding changes. That flexibility is part of what makes the repair-versus-replace decision more nuanced than it looks.
Before deciding whether to repair or replace, you need an honest assessment of what is wrong with the existing graphics. Damage on a part wrap generally falls into one of three categories, and the category determines your best option.
A repair is worth doing when the damage is small, the rest of the graphic is recent and in good condition, and the material can be matched or the repaired area can be visually isolated within the design. For example, if the bottom corner of a rear door has been scraped but the design element in that area is a solid block of colour, a skilled fitter can re-apply that section cleanly.
Repairs also make sense when the graphic is relatively new - typically under two years old - and the problem is a fitting fault rather than material failure. A lifting edge caused by poor application can be lifted back, the surface re-cleaned and re-adhered without replacing the whole panel section.
The practical limit on repairs is colour matching. Vinyl from even the same product range can vary slightly between print batches. If the damaged section is in the middle of a large unbroken area of colour, matching is very difficult and the repair is likely to show.
Full replacement of a panel's graphics makes more sense than repair in these situations:
Replacing the graphics on the affected panels gives you a clean start. Modern cast vinyl, applied properly to a prepared surface, will typically hold its colour and adhesion for several years under normal UK conditions.
A localised repair might cost a fraction of full panel replacement, but only if the repair is achievable. A patch job that shows is not a saving - it looks unprofessional and may put customers off. For a small business or sole trader working in and around Saffron Walden, the van is a moving advertisement and a poor-looking repair does the opposite of what branding is supposed to do.
Full replacement of a rear door pair, for example, typically costs somewhere in the range of £150 to £350 depending on panel size, design complexity and print cost. Replacing all branded panels on a standard panel van will generally cost more but is still significantly less than a full wrap, which covers the entire vehicle.
Get a quote for both options - repair and replace - before you decide. A contractor who designs and prints in-house can usually give you an accurate comparison quickly because they control both the print cost and the fitting.
One consideration that often catches people out is the cost and difficulty of removing the old graphic before new vinyl can go on. Old wraps that have been on a vehicle for several years can leave adhesive residue, particularly if the original material was lower quality or was applied over paint in poor condition.
Professional removal uses heat and the correct tools to lift the vinyl without damaging the underlying paintwork. If the paint underneath is compromised, that needs addressing before new vinyl is applied, otherwise adhesion will be poor from the start and you are setting the new graphic up to fail.
Ask your contractor whether removal and surface preparation are included in the quote for replacement, or whether they are additional costs. This is a point where quotes can look very different from one another.
We design and print in-house and travel to our customers, so the work is done at your location in or near Saffron Walden - no need to leave your van with a workshop.
If you are not sure whether your existing graphics are worth repairing or need replacing, call us and describe what you are seeing. We can usually give you an honest steer before we even visit.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsWe brand entire fleets of commercial vehicles in Cambridge with consistent, professionally printed graphics, designing and fitting everything…
See detailsLet us know what needs branding and we will send a design and price to look over.