Choosing the right materials and approach for your Newmarket fleet wrap is as important as the design itself - get it wrong and you will be paying to redo it sooner than you should.
Fleet managers and business owners in Newmarket often focus on the design when they think about vehicle branding. Colour, logo placement, contact details - these are the visible decisions. But the material the graphics are printed on and applied with has just as much impact on how the finished job looks and how long it lasts. This page sets out the main options honestly, with the trade-offs you need to know before you decide.
Cast vinyl is made by pouring liquid PVC compound onto a casting sheet, which produces a very thin, stable and highly conformable film. It follows the contours of a vehicle panel closely - around door handles, into recesses, over wheel arch lips - without the stress and lifting that stiffer films can produce. For a full vehicle wrap, cast film is the appropriate choice.
Cast film holds its dimensions well over time. Because it is not under internal stress, it does not tend to shrink at the edges after application, which is one of the main causes of lifted corners on cheaper jobs. It is also thinner, which means panel edges and seams look cleaner and less obvious on the finished vehicle.
The honest downside is cost. Cast film is more expensive than the alternative, and that cost passes through to the final price. For a full wrap on a large panel van, you are using a significant area of material, so the difference between film grades has a real impact on the total.
Calendered film is produced by passing vinyl compound through a series of rollers, which creates a thicker and less conformable material. It is cheaper to manufacture, and it works well on flat or gently curved surfaces - think flat body panels, doors on larger vehicles, or simple cut graphics on a plain surface.
The problem comes when calendered film is used on complex curves or around body detail. It tends to lift at edges and stress points because the film has memory - it wants to return to its flat original state. On a vehicle that is washed frequently and exposed to daily temperature changes, this stress accelerates edge lifting and premature failure.
For a Newmarket fleet operator running vehicles with straightforward panel shapes and wanting partial graphics or cut lettering rather than a full colour-change wrap, calendered film can be a practical and cost-effective option. For a full wrap intended to last several years on a vehicle that works hard, cast film is the better investment.
These are the two fundamental approaches to vehicle graphics, and they suit different briefs:
Any printed graphic applied to a commercial vehicle needs a protective overlaminate on top of the ink layer. Without it, the ink is vulnerable to petrol and chemical splashes, automated car washes, road abrasion and UV fade. A good quality laminate keeps the colour true and the surface protected from the kind of contact a working van encounters every day.
Overlaminates come in gloss, satin and matt finishes, and the choice affects how the finished vehicle looks. Gloss is vibrant and makes colours pop. Matt gives a flatter, more contemporary look and can disguise minor surface imperfections in older paintwork. Satin sits between the two. The finish choice is largely a branding decision, but it is worth knowing that matt overlaminates tend to show water marks more than gloss on vehicles that are not washed frequently.
A full wrap covers the entire vehicle in printed or coloured film. A partial wrap covers specific panels - typically the sides, rear, or a combination. Here is a plain comparison:
For a Newmarket fleet running multiple vehicles, colour consistency is one of the most important things to get right. If the same red appears slightly different on vehicles wrapped at different times, or by different suppliers, the fleet looks unprofessional even if each individual vehicle looks fine in isolation.
Where design and print are kept under one roof, the colour profiles used to produce the graphics can be controlled from design through to print, which makes it easier to match them on subsequent vehicles in the fleet. Outsourced print introduces variables that are difficult to control, and colour drift between print runs is a known issue when multiple suppliers or print processes are involved.
If your fleet has grown over time and vehicles were branded at different points, it is worth considering a planned rebrand that brings everything to the same standard. We can remove existing graphics and apply new consistent livery across the fleet, working in a phased schedule that keeps your vehicles operational throughout the process.
We travel to your premises in Newmarket to carry out installation. You do not need to arrange transport of vehicles to a workshop. If you want to talk through the material options for your specific fleet before committing to anything, call us and we will give you a straight assessment based on your vehicles, your brand and your budget.
Also available
We design, print and fit full or partial van wraps in Cambridge, working at your premises so your vehicle never leaves your site.
See detailsWe wrap commercial vehicles of all types in Cambridge, designing and printing everything in-house and fitting at your site.
See detailsA full van wrap transforms your entire vehicle into a moving advertisement for your business.
See detailsLet us know what needs branding and we will send a design and price to look over.